SANlight STIXX 4-100 LED 94W - 254 µmol/s (AA5030)

Product detailed description

Universal top light for medium tents

SANlight STIXX 4-100 is a linear LED light made up of four modules for medium growing areas with a depth of around 100 cm, vertical racks and installations with a low height above the plants. It delivers 254 µmol/s at 94 W and its asymmetrical optics distribute light homogeneously across the entire length of the light. IP68 protection means peace of mind even in damper conditions.

Parameters

• Power input: 94 W
• Photon flux PPF: 254 µmol/s
• Dimensions (LxWxH): 896x85x16.9 mm
• Weight: 1.35 kg
• Beam angle: 90/135°
• Module efficiency: 3.1 µmol/J (measured at 50% power, SANlight data)
• Spectrum: full spectrum 400-780 nm
• Protection: IP68
• Connector: M19 5-PIN
• LM90 lifespan: 53,000 h
• Warranty: 3 years
• Number of modules: 4
• Dimming: via the blue connector on the driver (M-Dimmer / Bluetooth Dimmer)

Compatibility

Compatible:

• Driver Set STIXX 4 (215 / 400 / 610 / 910 W) - powers this light (driver from the same series only)
• STIXX extension cables and splitters (T-Splitter, Y-Splitter), M19 5-PIN connector
• STIXX termination plug (AI5010) for unused DC ports on the driver
• SANlight dimmers M-Dimmer and Bluetooth Dimmer - via the blue connector on the driver
• Only lights of the same model on one driver

Incompatible:

• Drivers of other STIXX series - different output specification
• SANlight STIXX 50 - closed system with its own power unit
• EVO / Q-Series power cabling (Wieland connector) - different connector than M19
• FLEX II cabling (WDC19 connector) - different system

The light does not light up on its own - it needs a STIXX 4 driver

STIXX 4-100 is an LED light without its own power supply. To get it running, you need the Driver Set STIXX 4. According to SANlight's official table, the 215 W driver can power two 4-100 lights at full output, the 400 W and 610 W drivers three, and the 910 W driver five units. The driver, cables and accessories are purchased separately, so you can size the power supply exactly to the number of lights.

Which size to choose

4-100 is the middle of the range - a good choice when the 3-80 is too short and the 5-120 would extend beyond the edge of the area. If you need even more power for a longer space, compare it with the STIXX 5-120. You can connect more 4-100 lights with extension cables and M19 splitters.

Frequently asked questions

Which driver do I need for the STIXX 4-100?

Driver Set STIXX 4 - the 4-100 series has its own driver range (215, 400, 610 and 910 W). According to SANlight's official table, it can power 2 to 5 4-100 lights at full output (215 W two, 400 and 610 W three, 910 W five). The driver, cables and accessories are sold separately, so you can size the power supply exactly to the number of lights.

Can I combine the 4-100 with other STIXX lights on one driver?

No. One driver may only be used with identical lights of the same series - STIXX 4-100 with STIXX 4-100. You cannot mix the 4-100 with the 3-80, 5-120 or 6-150 on a shared driver. To expand, use additional 4-100 lights, extension cables and M19 splitters, and fit unused ports with a termination plug.

How do I dim the STIXX 4-100?

Dimming runs through the driver: connect the magnetic M-Dimmer or Bluetooth Dimmer SANlight to its blue connector, or a 0-10V signal. The driver recognises the number of connected modules and distributes power between them, so you control the entire powered branch at once.