SANlight Driver Set STIXX 4, 400 W (AI5107)
Code: N52827



Related products
Product detailed description
Power supply for a full STIXX 4-100 tent
SANlight Driver Set STIXX 4, 400 W is a Smart Driver for the STIXX 4-100 series, with capacity for three lights at full power. Three 4-100 lights illuminate a large tent evenly, which is why this version is popular as the heart of a complete growing setup. It powers the STIXX 4 series exclusively.
The driver is supplied without lights or cables. For operation, it requires STIXX 4-100 lights, which are purchased separately and do not light up without the driver.
Power cable for connecting the driver
A separate SANlight power cable, which is not included, is required to connect the driver to the mains. You can choose from two compatible variants:
- SANlight power cable for Q-Series Gen2 – variant with a straight connector.
- Angled SANlight power cable for EVO/Q-Series – variant with an angled connector.
Both cables are used to power this driver from the mains. Cables and splitters for connecting the driver to STIXX lights are selected separately according to the setup.
Specifications
- Type: power driver (Smart Driver) for the STIXX series
- Maximum output power: 400 W
- Designed for: STIXX 4-100 lights (same series only)
- At full power (official SANlight table): three lights (3 x 94 W = 282 W)
- Rated power consumption of one light: 94 W
- Max. output current: 5.2 A
- Typical output voltage: 77 V DC
- Dimensions (L x W x H): 281 x 90 x 41.5 mm
- Weight: 1.98 kg
- Input voltage: 120-240/277 V AC, 50/60 Hz
- Dimming: blue connector on the driver (M-Dimmer, Bluetooth Dimmer or 0-10V)
- Unused DC ports: termination plug (mandatory)
- Water resistance: M19 connector on the light, IP68; the driver's mains plug is not water-resistant
Compatibility
Compatible:
- SANlight STIXX 4-100 and Undercanopy STIXX 4-100 lights – three lights at full power
- SANlight termination plug (AI5010) for unused DC ports on the driver
- SANlight M-Dimmer and Bluetooth Dimmer dimmers, or a 0-10V signal (blue connector on the driver)
- M19 extension cables and splitters (5 PIN) from STIXX accessories for connecting multiple lights
Not compatible:
- other STIXX series (2-60, 3-80, 5-120 and 6-150) – the driver is designed only for its own series
- mixing different STIXX models on one driver – identical lights are required
- STIXX 50 – a closed system with its own power supply and different cabling
- EVO and FLEX II lights – different connector and power supply
When to choose the 400 W version
According to the official SANlight table, the 400 W driver powers three STIXX 4-100 lights at full power. If you are planning only two lights, the smaller 215 W driver is sufficient; for more than three lights at full power, choose the 910 W version, which powers five lights. The more powerful 610 W driver powers the same three lights, but with greater current capacity. The Smart Driver can also operate fewer lights, so you can build the setup gradually.
Dimming on the driver and port termination
The driver controls the light level: connect a Bluetooth Dimmer or SANlight M-Dimmer to the blue connector, or use a 0-10V signal, and the brightness of all lights changes simultaneously. Unused driver ports must be closed with a termination plug – without it, the system may be damaged.
Protection and installation
The light has IP68 protection at the M19 connector; the driver's mains plug is not water-resistant and its connection must be kept away from moisture. Do not stack drivers on top of one another and leave at least 10 mm between them.
Frequently asked questions
How many STIXX 4-100 lights does the 400 W driver power?
At full rated power, it powers three STIXX 4-100 lights (3 x 94 W = 282 W) – this number is given in the official SANlight table. You can connect a fourth light, but all of them will then switch to reduced power. For full light output, allow for three lights.
What happens if I do not fill all the driver ports?
Nothing; you do not need to fill them immediately. The Smart Driver recognises how many STIXX 4-100 lights are connected, and unused ports are not a problem – simply close them with termination plugs. Each light operates at full power up to the maximum number of lights; the driver detects when a light is added or disconnected.
What is the termination plug for, and do I need one?
Yes, it is mandatory. The driver has more DC ports than you would normally use for lights, and every unused port must be closed with a termination plug (AI5010). Without it, the system may be damaged. It is an inexpensive but essential part – the manufacturer does not supply the plug with the lights or driver; it must be purchased separately.