SANlight Driver Set STIXX 4, 215 W (AI5103)
Code: N52823



Related products
Product detailed description
Input power supply for the STIXX 4-100 range
SANlight Driver Set STIXX 4, 215 W is the smallest Smart Driver for STIXX 4-100 linear lights. At full power, it can run two lights, making it suitable for a smaller tent or wherever a pair of STIXX 4-100 lights is sufficient. The driver is intended only for the STIXX 4 range.
It is sold separately, without lights or cables. The STIXX 4-100 light is only an LED light without a power supply and will not illuminate without a driver.
Power cable for connecting the driver
A separate SANlight power cable, which is not included, is required to connect the driver to the mains. You can choose from two compatible variants:
- SANlight power cable for Q-Series Gen2 – variant with a straight connector.
- Angled SANlight power cable for EVO/Q-Series – variant with an angled connector.
Both cables supply power to this driver from the mains. Cables and splitters for connecting the driver to STIXX lights are selected separately according to the configuration.
Specifications
- Type: power driver (Smart Driver) for the STIXX range
- Maximum output power: 215 W
- Designed for: STIXX 4-100 lights (same range only)
- At full power (official SANlight table): two lights (2x 94 W = 188 W)
- Rated power consumption of one light: 94 W
- Max. output current: 2.8 A
- Typ. output voltage: 76 V DC
- Dimensions (L x W x H): 281 x 90 x 41.5 mm
- Weight: 1.9 kg
- Input voltage: 120-240/277 V AC, 50/60 Hz
- Dimming: blue connector on the driver (M-Dimmer, Bluetooth Dimmer or 0-10V)
- Unused DC ports: termination cap (mandatory)
- Water resistance: M19 connector on the light IP68; the driver's mains plug is not water-resistant
Compatibility
Compatible:
- SANlight STIXX 4-100 and Undercanopy STIXX 4-100 lights – two lights at full power
- SANlight termination cap (AI5010) for unused DC ports on the driver
- SANlight M-Dimmer and Bluetooth Dimmer dimmers, or a 0-10V signal (blue connector on the driver)
- M19 (5 PIN) extension cables and splitters from STIXX accessories for connecting multiple lights
Not compatible:
- other STIXX ranges (2-60, 3-80, 5-120 and 6-150) – the driver is intended only for its own range
- mixing different STIXX models on one driver – identical lights are required
- STIXX 50 – closed system with its own power supply and different cabling
- EVO and FLEX II lights – different connector and power supply
Two lights for a smaller tent
According to the official SANlight table, the 215 W driver can run two STIXX 4-100 lights at full power. If you want three lights, choose the 400 W version; for five lights at full power, choose up to the 910 W driver. Buying a more powerful power supply straight away is worthwhile if you are planning to expand the setup – the driver cannot be upgraded later; the whole unit must be replaced.
Brightness control and unused ports
Control is centralised via the driver: the blue connector accepts the magnetic M-Dimmer, SANlight Bluetooth Dimmer and a 0-10V input, and controls the brightness of all connected lights. Unused DC ports must not be left open – fit each one with a termination cap, as prescribed by the manufacturer to protect the system.
Water resistance and installation
Only the M19 connector on the light is water-resistant (IP68); keep the driver's mains plug dry. When using multiple drivers, maintain a minimum distance of 10 mm between them and do not stack them.
Frequently asked questions
How many STIXX 4-100 lights can this driver run?
At full rated power, it can run two STIXX 4-100 lights (2x 94 W = 188 W) – this number is specified in the official SANlight table. A third light can be connected, but the power will then be divided between all of them and the lights will operate below full power. For maximum light, stick to two.
Do all lights on the driver have to be identical?
Yes, they do. Only identical lights from one range may be connected to a shared driver – STIXX 4-100 therefore only with another STIXX 4-100. Two different STIXX models must not be connected to one power supply, as each range has a different power consumption. If you are expanding with another model, buy a separate driver for it; connect identical lights using M19 extension cables and splitters.
Do I need a termination cap for the driver?
Yes. The driver has more DC ports than you will typically use, and unused ports must be closed with a termination cap (AI5010). Without one, the system may be damaged, so consider it an essential part of the setup. It is supplied separately, not with the driver or lights.