SANlight Driver Set STIXX 4, 610 W (AI5111)
Code: N52831



Related products
Product detailed description
STIXX 4 Driver with 8 A current
SANlight Driver Set STIXX 4, 610 W is a powerful Smart Driver for the STIXX 4-100 range. According to the official SANlight table, it can power three STIXX 4-100 lights at full power – the same as the 400 W version, but with a higher output current (8 A) and greater reserve for a longer chain and adding more lights later. It powers only the STIXX 4 range.
The driver is sold separately, without lights and cables. You fit it with STIXX 4-100 lights, which do not illuminate on their own.
Power cable for connecting the driver
A separate SANlight power cable, which is not included, is required to connect the driver to the mains. You can choose from two compatible variants:
- SANlight power cable for Q-Series Gen2 – variant with a straight connector.
- Angled SANlight power cable for EVO/Q-Series – variant with an angled connector.
Both cables are used to power this driver from the mains. Cables and splitters for connecting the driver to STIXX lights are selected separately according to the configuration.
Specifications
- Type: power driver (Smart Driver) for the STIXX range
- Maximum output power: 610 W
- Designed for: STIXX 4-100 lights (same range only)
- At full power (official SANlight table): three lights (3 x 94 W = 282 W)
- Rated power consumption of one light: 94 W
- Max. output current: 8.0 A
- Typical output voltage: 76 V DC
- Dimensions (L x W x H): 391 x 90 x 41.5 mm
- Weight: 2.82 kg
- Input voltage: 120-240/277 V AC, 50/60 Hz
- Dimming: blue connector on the driver (M-Dimmer, Bluetooth Dimmer or 0-10 V)
- Unused DC ports: termination plug (mandatory)
- Water resistance: M19 connector on the light IP68; the driver's mains plug is not water-resistant
Compatibility
Compatible:
- SANlight STIXX 4-100 and Undercanopy STIXX 4-100 lights – three lights at full power
- SANlight termination plug (AI5010) for unused DC ports on the driver
- SANlight M-Dimmer and Bluetooth Dimmer dimmers, or a 0-10 V signal (blue connector on the driver)
- M19 (5 PIN) extension cables and splitters from STIXX accessories for connecting multiple lights
Incompatible:
- Ostatní STIXX ranges (2-60, 3-80, 5-120 and 6-150) – the driver is intended only for its own range
- Mixing different STIXX models on one driver – identical lights are required
- STIXX 50 – closed system with its own power supply and different cabling
- EVO and FLEX II lights – different connector and power supply
Reserve and centralised distribution
The driver powers three STIXX 4-100 lights at full power according to the official SANlight table – the same number as the 400 W version, but with an output current of 8 A and greater reserve. The advantage is shared dimming and simpler distribution across the entire area. You can also connect additional lights to the three-light setup, which will then run at reduced power. If you want five lights at full power, choose the higher-output 910 W version.
Termination plug and dimming
Unused DC ports on the driver must be fitted with a termination plug – without it, the system may be damaged, so treat it as a mandatory part of every setup. Dimming is performed directly on the driver: connect the SANlight magnetic M-Dimmer or Bluetooth Dimmer to its blue connector, or use a 0-10 V control signal. All lights are then dimmed together.
Water resistance
While the M19 connector on the light can withstand moisture (IP68), the driver's mains plug cannot – protect it from water. Do not stack multiple drivers on top of one another and leave at least 10 mm between them.
Frequently asked questions
How many STIXX 4-100 lights can the 610 W driver power?
At full rated power, it can power three STIXX 4-100 lights (3 x 94 W = 282 W) – this is the number specified in the official SANlight table. The driver has a high output current of 8 A, so reserve remains even above three lights; however, additional lights run at reduced power. The 910 W version is available for five lights at full power.
Can I connect different STIXX models to one driver?
No. One driver may only be connected to identical lights from the same STIXX range – for example, STIXX 4-100 with STIXX 4-100. The manufacturer prohibits combinations such as STIXX 2-60 and STIXX 3-80 on one driver. To connect more lights of the same model, use M19 extension cables and splitters, and fit termination plugs to unused ports.
Will the driver also work with fewer lights than the maximum?
Yes. The Smart Driver detects how many lights are connected and adjusts their power accordingly. Up to the full number of lights, each STIXX 4-100 light runs at full power; you can therefore start with one and add more over time. Fit termination plugs to any unused DC ports.