SANlight Driver Set STIXX 4, 910W (AI5114)
Code: N52834



Related products
Product detailed description
The most powerful driver in the STIXX 4 range
SANlight Driver Set STIXX 4, 910W is the top model in the STIXX 4 range – a Smart Driver that powers up to five STIXX 4-100 lights from a single location. It is suitable for spacious grow rooms and multi-level setups, where one powerful source is more manageable than a handful of small drivers spread across the area. It powers the STIXX 4 range exclusively.
The driver is supplied without lights or cables and is purchased separately. You can illuminate it with STIXX 4-100 lights, which will remain dark without a driver.
Power cable for connecting the driver
A separate SANlight power cable, which is not included, is required to connect the driver to the mains. You can choose from two compatible variants:
- SANlight power cable for Q-Series Gen2 – variant with a straight connector.
- Angled SANlight power cable for EVO/Q-Series – variant with an angled connector.
Both cables are used to power this driver from the mains. Cables and splitters for connecting the driver to STIXX lights are selected separately according to the setup.
Specifications
- Type: power driver (Smart Driver) for the STIXX range
- Maximum output power: 910 W
- Designed for: STIXX 4-100 lights (same range only)
- At full power (official SANlight table): five lights (5x 94 W = 470 W)
- Rated power consumption of one light: 94 W
- Max. output current: 11.9 A
- Typical output voltage: 76 V DC
- Dimensions (L x W x H): 399 x 90 x 41.5 mm
- Weight: 3.11 kg
- Input voltage: 120-240/277 V AC, 50/60 Hz
- Dimming: blue connector on the driver (M-Dimmer, Bluetooth Dimmer or 0-10V)
- Unused DC ports: termination cap (mandatory)
- Water resistance: M19 connector on the light IP68; the driver's mains plug is not water-resistant
Compatibility
Compatible:
- SANlight STIXX 4-100 and Undercanopy STIXX 4-100 lights – five lights at full power
- SANlight termination cap (AI5010) for unused DC ports on the driver
- SANlight dimmers M-Dimmer and Bluetooth Dimmer, or a 0-10V signal (blue connector on the driver)
- M19 (5 PIN) extension cables and splitters from STIXX accessories for connecting multiple lights
Not compatible:
- Ostatní STIXX ranges (2-60, 3-80, 5-120 and 6-150) – the driver is intended only for its own range
- Mixing different STIXX models on one driver – identical lights are required
- STIXX 50 – closed system with its own power source and different cabling
- EVO and FLEX II lights – different connector and power supply
Why choose the largest driver straight away
The driver powers five STIXX 4-100 lights (5x 94 W = 470 W) at full power according to the official SANlight table – the most in the STIXX 4 range. Buying the largest power supply straight away is worthwhile for a large setup that you do not want to build later from several drivers. Smart Driver Technology also allows you to run a smaller number of lights at full power and add the rest as the growing area expands.
Dimming and termination
Dimming is handled by the driver, not the lights: connect a magnetic M-Dimmer, Bluetooth Dimmer SANlight or a 0-10V signal to its blue connector to regulate the entire setup at once. Each unused DC port must then be closed with a termination cap – this is mandatory, as failure to do so may damage the system.
IP rating and clearances
The IP68 rating applies to the M19 connector on the light; the driver's mains plug is not water-resistant. Do not stack the drivers; leave a gap of at least 10 mm between them.
Frequently asked questions
How many STIXX 4-100 lights can the 910W driver handle?
At full rated power, it can handle five STIXX 4-100 lights (5x 94 W = 470 W) according to the official SANlight table. This is the maximum for the STIXX 4 range. The driver also works with more than five lights; it simply distributes the power between all of them, and the lights operate at a reduced level.
Can I start with one light and add more gradually?
Yes, without any problems. The driver also works with a single light: Smart Driver Technology detects the number of connected STIXX 4-100 lights and distributes the power between them automatically. Up to the full number of lights, each runs at full power; above that number, the power is spread across them and the lights operate at a lower level. You can therefore start with a small setup and build up to the recommended number.
Why must unused driver ports be capped?
Every DC port on the driver that is not used for a light must be fitted with a termination cap (AI5010) – otherwise the system may be damaged. It is a small and inexpensive part, but it is not optional. The cap is not included with the driver or light, so remember to purchase one when building the setup.