SANlight Driver Set STIXX 5, 400W (AI5108)
Code: N52828



Related products
Product detailed description
Two 5-120 lights with extra reserve
SANlight Driver Set STIXX 5, 400W is a Smart Driver for the STIXX 5-120 range. According to the official SANlight table, it can power two lights at full output – just like the smaller 250W version, but with a higher output current (4.2 A) and reserve capacity for a longer chain and adding lights later (these then run at reduced output). It powers the STIXX 5 range exclusively.
The driver is supplied without lights and cables and is purchased separately. To illuminate the setup, add STIXX 5-120 lights, which do not illuminate without a driver.
Power cable for connecting the driver
A separate SANlight power cable, which is not included, is required to connect the driver to the mains. You can choose from two compatible variants:
- SANlight power cable for Q-Series Gen2 – variant with a straight connector.
- SANlight Angled power cable for EVO/Q-Series – variant with an angled connector.
Both cables power this driver from the mains. Cables and splitters for connecting the driver to STIXX lights are selected separately according to the setup.
Specifications
- Type: power driver (Smart Driver) for the STIXX range
- Maximum output power: 400 W
- Designed for: STIXX 5-120 lights (same range only)
- At full output (official SANlight table): two lights (2x 117 W = 234 W)
- Rated power consumption of one light: 117 W
- Max. output current: 4.2 A
- Typical output voltage: 95 V DC
- Dimensions (L x W x H): 281 x 90 x 41.5 mm
- Weight: 1.98 kg
- Input voltage: 120-240/277 V AC, 50/60 Hz
- Dimming: blue connector on the driver (M-Dimmer, Bluetooth Dimmer or 0-10V)
- Unused DC ports: termination cap (mandatory)
- Water resistance: M19 connector on the light IP68; the driver's mains plug is not water-resistant
Compatibility
Compatible:
- SANlight STIXX 5-120 and Undercanopy STIXX 5-120 lights – two lights at full output
- SANlight termination cap (AI5010) for unused DC ports on the driver
- SANlight M-Dimmer and Bluetooth Dimmer, or a 0-10V signal (blue connector on the driver)
- M19 (5 PIN) extension cables and splitters from STIXX accessories for connecting multiple lights
Not compatible:
- Ostatní STIXX ranges (2-60, 3-80, 4-100 and 6-150) – the driver is intended only for its own range
- Mixing different STIXX models on one driver – identical lights are required
- STIXX 50 – closed system with its own power supply and different cabling
- EVO and FLEX II lights – different connector and power supply
When the 400W version is the right choice
The smaller 250W driver can also handle two STIXX 5-120 lights at full output, so choose the 400W version for extra reserve: the higher current and wattage leave room to add further lights to the pair, which will then run at slightly reduced output. If you want three lights at full output, choose the 610W version.
Brightness control and unused ports
Brightness is controlled centrally through the driver: the blue connector accepts the magnetic M-Dimmer, SANlight Bluetooth Dimmer and 0-10V input, controlling the brightness of all connected lights. Unused DC ports must not be left open – fit each one with a termination cap, as prescribed by the manufacturer to protect the system.
Water resistance
The M19 connector on the LED light is water-resistant (IP68), but the driver's mains plug is not – protect its connection to the socket from moisture. Leave a gap of at least 10 mm between multiple drivers and do not stack them on top of each other.
Frequently asked questions
How many STIXX 5-120 lights does the 400W driver power?
At full rated output, it powers two STIXX 5-120 lights (2x 117 W = 234 W) – this number is stated in the official SANlight table (the same as for the 250W version, but with more reserve). You can connect a third light, but it will run at reduced output. For three lights at full output, choose the 610W version.
What happens if I do not fill all the driver's ports?
Nothing; you do not have to fill them immediately. The Smart Driver detects how many STIXX 5-120 lights are connected, and unused ports are not a problem – simply close them with termination caps. Up to the full number of lights, each one operates at full output; the driver detects when a light is added or disconnected.
What is the termination cap for, and do I need one?
Yes, it is mandatory. The driver has more DC ports than you will usually connect lights to, and each unused port must be closed with a termination cap (AI5010). Without one, the system may be damaged. It is an inexpensive but essential component – the manufacturer does not supply the cap with the lights or driver; it must be purchased separately.