SANlight Driver Set STIXX 2, 160 W (AI5100)

Product detailed description

Input power supply for STIXX 2-60 systems

SANlight Driver Set STIXX 2, 160 W is the smallest power driver in the STIXX 2 - Smart Driver range, powering STIXX 2-60 linear lights. These are suitable above seedlings, cuttings and in vertical or multi-level installations where uniform but not excessively intense light is required. The driver is intended exclusively for the STIXX 2 range.

The STIXX 2-60 light itself is only an LED light without a power supply – it requires this driver to operate, and STIXX 2-60 lights are purchased separately. The driver is supplied without lights, a mains power cable, distribution cables or extension cables.

Power cable for connecting the driver

A separate SANlight power cable, which is not included in the package, is required to connect the driver to the mains. You can choose from two compatible variants:

• SANlight power cable for Q-Series Gen2 – version with a straight connector.
• Angled SANlight power cable for EVO/Q-Series – version with an angled connector.

Both cables supply this driver from the mains. Cables and splitters for connecting the driver to STIXX lights are selected separately according to the system.

Specifications

• Type: power driver (Smart Driver) for the STIXX range
• Maximum output power: 160 W
• Intended for: STIXX 2-60 lights (same range only)
• At full power (official SANlight table): three lights (3 x 47 W = 141 W)
• Rated power consumption of one light: 47 W
• Max. output current: 4.2 A
• Typical output voltage: 38 V DC
• Dimensions (L x W x H): 231 x 90 x 41.5 mm
• Weight: 1.6 kg
• Input voltage: 120-240/277 V AC, 50/60 Hz
• Dimming: blue connector on the driver (M-Dimmer, Bluetooth Dimmer or 0-10V)
• Unused DC ports: terminating cap (mandatory)
• Water resistance: M19 connector on the light IP68; the driver's mains plug is not water-resistant

Compatibility

Compatible:

• SANlight STIXX 2-60 and Undercanopy STIXX 2-60 lights – three lights at full power
• SANlight terminating cap (AI5010) for unused DC ports on the driver
• SANlight M-Dimmer and Bluetooth Dimmer dimmers, or a 0-10V signal (blue connector on the driver)
• M19 (5 PIN) extension cables and splitters from STIXX accessories for connecting multiple lights

Not compatible:

• Ostatní STIXX ranges (3-80, 4-100, 5-120 and 6-150) – the driver is intended only for its own range
• mixing different STIXX models on one driver – identical lights are required
• STIXX 50 – closed system with its own power supply and different cabling
• EVO and FLEX II lights – different connector and power supply

How many lights it can handle and how Smart Driver works

At full power, the 160 W driver can power three STIXX 2-60 lights – this is stated in the official SANlight table. Smart Driver Technology automatically detects how many lights are connected: up to three lights run at full power, while a fourth is powered at reduced output because the power is distributed between all of them. Technically, this is possible, but for maximum light, stay with three.

Terminating cap and dimming

Unused DC ports on the driver must be fitted with terminating caps – without them, the system may be damaged, so consider them a mandatory part of every system. Dimming is performed directly on the driver: connect a magnetic M-Dimmer or SANlight Bluetooth Dimmer to its blue connector, or use a 0-10V control signal. The lights are then dimmed together.

Protection and installation

The light has IP68 protection at the M19 connector; the driver's mains plug is not water-resistant and its connection must be kept away from moisture. Do not stack the drivers and leave at least 10 mm between them.

Frequently asked questions

How many STIXX 2-60 lights can this driver power?

It can power three STIXX 2-60 lights at full rated output – this number is stated in the official SANlight table. You can connect more lights, but the power will then be distributed between all of them and the lights will operate at reduced output. For maximum light, therefore, plan for three lights; add more only deliberately.

Can I connect different STIXX models to one driver?

No. Only identical lights from the same STIXX range may be connected to one driver – for example, STIXX 2-60 with STIXX 2-60. The manufacturer prohibits combinations such as STIXX 2-60 and STIXX 3-80 on a shared driver. For more lights of the same model, use M19 extension cables and splitters, and fit terminating caps to unused ports.

What is the terminating cap for, and do I need one?

Yes, it is mandatory. The driver has more DC ports than you will usually connect lights to, and every unused port must be closed with a terminating cap (AI5010). Without it, the system may be damaged. It is an inexpensive but essential part – the manufacturer does not supply the cap with the lights or driver; it must be purchased separately.